Aviom 6416dio User Manual Page 76
- Page / 113
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
66re A r PA N e l Fe A t u r e s
A-Net Ports
Two EtherCon jacks are provided for A‑Net connections, labeled A and B.
Connections can use standard RJ45‑style cables or cables outfitted with
the locking EtherCon connector. Refer to the section on network modes for
additional information about using these jacks.
Digital Inputs and Outputs
Two versions of the 6416dio Digital I/O Module are manufactured, one with
DB25 multipin connectors and another with BNC connectors.
DB25 Version I/O
Sixteen digital input and output channels are available on two female DB25
multipin connectors, eight I/O channels per connector. The AES3 format
provides pairs of digital audio channels on each XLR connector. Each DB25
multipin on the 6416dio provides eight channels of AES3 input and eight
channels of AES3 output simultaneously. Breakout cables for the DB25
multipin jacks used with the 6416dio should be configured with four male
XLR jacks and four female XLR jacks.
The 6416dio module’s DB25 connectors are designed to accept digital signals
whose wiring conforms to either the Yamaha‑compatible or Digidesign/
Tascam‑compatible pinouts. Always use cables configured for the device
that the 6416dio is being connected to; the two common wiring conventions
(Yamaha and Digidesign/Tascam compatible) are not interchangeable.
TERMINATION
B
A
Digital I/O Module
I/O CHANNELS –6 –
6 416
dio
AC POWER
PIN = GND
VDC
IN
OUT
RS-/
FUSE: VAC- FAL
BACKUP POWER
GPIO INPUT
UP = ISOLATED
DN =TTL
PORT SETUP
–8
CTRL MASTER
/
RESERVED,
ON
WORD CLOCK
IN
TERMINATION
OUT
DIGIDESIGN / TASCAM COMPATIBLE
YAMAHA COMPATIBLE
VIRTUAL DATA CABLE PORTS
The 6416dio can transmit and receive AES data using either the Digidesign/
Tascam-compatible or Yamaha-compatible wiring pinouts.
P No t e : It is not possible to use the Digidesign/Tascam‑compatible and
Yamaha‑compatible DB25 I/O connections on the same set of
6416dio channels simultaneously.
- 6 416 dio 1
- READ THIS FIRST 3
- Important Safety Instructions 3
- WARNING! 4
- Aviom, Inc. Limited Warranty 5
- Warranty Information 6
- Table of Contents 7
- Features 11
- The EtherCon Connector 12
- Package Contents 12
- About AES3 and AES-3id 13
- Firmware Notice 14
- About A-Net 15
- Control Data 16
- A-Net Ports 16
- 7Ab o u t A-Ne t 17
- AC Power 18
- AC Line Conditioning 18
- Rack Mounting 18
- Ventilation 19
- Cleaning 19
- Pro64 Interface Conventions 20
- Selecting Values 21
- DIP Switches 21
- Pro64 User Interface 22
- A-Net Slot 23
- Slots and Sample Rate 24
- A-Net Slot Display 25
- A-Net Slot Example 27
- Network Modes 29
- Control Master 31
- Control Master Functions 32
- Changing Settings 33
- 24co N t r o l mA s t e r 34
- Network Sample Rate 35
- Auto/Manual Mode Selection 36
- Managed Mode 37
- Password Protection 38
- 29co N t r o l mA s t e r 39
- Front Panel Components 40
- Rear Panel Components 42
- Digital I/O Module 43
- Front Panel Features 46
- A-Net Slot Configuration 47
- Bank Select 48
- Network Mode 49
- A-Net Transmit/Receive 50
- Manual Mode - Receive 51
- Clock Master 52
- Clock Sources 53
- Sample Rate 54
- Changing the Sample Rate 55
- Clock Errors 56
- Channel Activation Button 57
- AES Data Valid LEDs 58
- Signal Present LEDs 58
- Stereo Link Button 58
- Managed Button 59
- Edit Lock Button 60
- VDC Configuration 61
- VDC Slot Display 62
- VDC In Use LED 63
- Assigning a VDC Slot 63
- Deactivate an Active VDC Slot 64
- Advanced Functions 65
- Function Button 66
- Password Unlock 67
- Set a New Password 67
- Sample Alignment 68
- Firmware Update 71
- Error Recovery 72
- Firmware Update - via A-Net 72
- Restore Factory Defaults 73
- 64Fi r m w A r e uP d A t e 74
- Rear Panel Features 75
- Digital Inputs and Outputs 76
- DB25 Version I/O 76
- DB25 Pinout 77
- BNC Version I/O 78
- Virtual Data Cables 80
- RS-232/422 Port 81
- RS-232/422 Baud Rates 83
- Control Master DIP Switch 83
- RS-232/422 Pinout Information 85
- 76rs-232/422 86
- Creating Custom Cables 87
- Building a Pro64 Network 88
- Auto Mode Connections 89
- Digital Copies in Auto Mode 90
- Manual Mode Connections 92
- Digital Copies in Manual Mode 96
- Specifications 99
- 90sP e c i F i c A t i o N s 100
- 91sP e c i F i c A t i o N s 101
- Dimensions 102
- GPIO Specifications 103
- Factory Default Settings 104
- 6416dio Block Diagram 105
- 96iN d e x 106
- 97iN d e x 107
- 98iN d e x 108
- 99iN d e x 109
- 100iN d e x 110
- 101iN d e x 111
- Warranty Registration 112
Related products and manuals for Accessories for air Aviom 6416dio
Accessories for air Aviom 6416Y2 User Manual
(92 pages)
(92 pages)
© 2020, manymanuals.com. All rights reserved. | 0.425 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals